基于Isograph的FMECA分析在潜孔钻机中的应用

为提高潜孔钻机的可靠性,利用FMECA分析方法并结合Isograph软件对潜孔钻机进行FMECA分析。通过对潜孔钻机FMECA分析,确定了潜孔钻机危害性最高的组成结构,提出了预防维护的措施,为提高潜孔钻机的可靠性提供了依据。     

龙滩水电站地下厂房进水口高边坡加固支护设计

龙滩水电站地下厂房进水口高边坡开挖坡高达435m，坡面面积达27万m^2，为典型的反倾向层状结构岩质高边坡。为了确保进水口坝段的稳定，必须保持边坡岩体有足够的稳定性，通过采取边坡轮廓设计，防渗、排水设计，加固支护设计及施工控制等一系列措施，确保边坡稳定。文章简要论述了边坡设计的原则、标准、高边坡轮廓设计、防渗排水系统、加固支护措施、施工控制等情况。     

Nanoscale Crystallization in Amorphous Fe–P–Mn Alloys

Mössbauer effect measurements and physicochemical analysis demonstrate that annealing of amorphous Fe–P–Mn alloys leads to the formation of a nanocrystalline structure.     

A biochar from casein and its properties

A biochar was prepared by pyrolysis of casein. A helium and mercury porosimeter were used to measure the true and apparent densities of the chars respectively, elemental and IR analysis were used to characterize the chemical composition of char. A SEM was used to observe the char surfaces in order to verify the presence of porosity. The biochar has 9.02% of nitrogen, content of porosity is 20%. The experimental results show that it is possible to prepare chars with relatively high porosity from casein for the further preparation of activated carbon.     

在二(2-乙基己基)磷酸钠的微乳液中金属萃合物对水增溶的影响

测算了由二（2－乙基己基）磷酸钠，金属盐（CoSO4,NiSO4,ZnSO4,MgCl2或Cr(NO3)3)水溶液，正辛醇和正辛烷组成的微乳液中正辛醇从连续油相到界面的ΔGo→i^o和水的极限增容量φ'H2O。用金属萃取络合物反胶束的形成及其亲油性解释了金属离子对φ'H2O和ΔGo→i^o的影响。     

Increasing the service properties of weld joints by electrohydroimpulse treatment

Known examples of the positive influence of electrohydroimpulse treatment on the quality of weld joints of various steels, particularly including an increase in their long-term and cyclic strength and also corrosion resistance, are analyzed. It is shown that in this case there is a reduction in residual macro- and micro-stresses and also a change in the parameters of the dislocation structure of the joint metal in the direction of stabilization of it.Translated from Problemy Prochnosti, No. 4, pp. 119–123, April, 1996.     

插补法CAI研究

数字程序控制计算机辅助教学是将计算机技术用于数字程序控制的教学过程，它帮助学生学习并模拟教学实验．本文介绍了数字程序控制中直线插补和圆孤插补的ＣＡＩ实现方法．